Outstanding high-grade gold intercepts at Tabakorole
Released
Released
Announcement PDF
26 April 2022
LONE WOLF DELIVERS OUTSTANDING HIGH-GRADE
GOLD INTERCEPTS
HIGHLIGHTS
Results received for 5 shallow Reverse Circulation (RC) drillholes at the Lone Wolf
Prospect, aiming to test the tenor of mineralisation under artisanal workings.
Three holes hit mineralisation with a best intercept of 14m at 4.9g/t Au from 33m
including 4m at 16.3gt/t Au from 33m.
Mineralisation remains open along strike and at depth.
One Aircore hole at Target H at Tabakorole (refer Figure 3) reported mineralisation,
returning 7m at 2.1g/t Au from 26m and ending in mineralisation.
Marvel Gold Limited (ASX: MVL) (Marvel or the Company) is pleased to announce the
results of RC drilling at the Lone Wolf Prospect (Lone Wolf) on the Tabakorole License
(Tabakorole or the Project), located in southern Mali. The Tabakorole License is held
under a joint venture with Altus Strategies plc, in which Marvel holds a 70% interest.
During March 2022, the Company completed a 5-hole reconnaissance RC drilling
program, for a total of 415m at Lone Wolf located approximately 3km south of
Tabakorole in an area that was previously the subject of artisanal mining activity.
Historical drilling at Lone Wolf intersected 12m at 1.2g/t Au from surface (ASX
announcement 17th June 2020) and was followed up by Marvel with Aircore drilling
which intersected 4m at 1.3g/t Au from 8m and 4m at 2.7g/t Au from 20m (ASX
announcement 8th July 2021), ending in mineralisation.
The shallow RC program was designed to test whether Lone Wolf hosts potentially
economic mineralisation by drilling follow-up RC holes on sections 50m to either side of
the mineralised Aircore intercept.
The program successfully intersected mineralisation in 3 out of 5 holes with best
intercepts recorded in hole 22TBKRC021:
8m at 1.8g/t Au from 16m and
14m at 4.9g/t Au (including 4m at 16.3gt/t Au) from 33m and
10m at 1.9g/t Au from 55m
Additional notable intercepts included:
6m at 1g/t Au from 1m and 11m at 0.9g/t Au from 64m in hole 22TBKRC017; and
4m at 0.9g/t Au from 63m in hole 22TBKRC019.
Managing Director Chris van Wijk commented: “We are very pleased with this initial
drilling campaign at Lone Wolf which has confirmed the presence of high-grade gold
over significant widths. Drilling was designed to de-risk the prospect and uncover the
bedrock mineralisation which has been largely obscured by oxidised cover rocks. The
RC chips have shown that the prospect is well mineralised and that mineralisation
correlates well with the sulphide content. These results have given us the confidence to
embark on further exploration at Lone Wolf, commencing with an IP survey to assist
with identifying the most chargeable zones that is currently under way.”
The initial interpretation of Lone Wolf was that mineralisation was associated with the
contacts of a magnetic low unit (interpreted as a granite body) within the surrounding
metasediments (See Figures 1 and 2 below). Artisanal miners had initially set about
mining the base of the laterite, however had transitioned to mining the in-situ
mineralisation following the completion of the Company’s 2021 Aircore drilling program.
Due to the artisanal workings, drillholes had to be drilled towards both the north-east
and south-west to intersect the mineralisation which is believed to be sub-vertical and
trending in a north-northwesterly direction based on the artisanal workings.
The current RC program has shown that the mineralisation is hosted both within a unit
logged as a metagreywacke (a metamorphosed mudstone) but with the best intercepts
being within granitic host rocks and at or near to the contacts with the metasediments.
The mineralisation in the drillholes was associated with sulphides (Pyrite and Pyrrhotite)
with visual estimates up to 10% sulphides in RC chips. This suggests that Induced
Polarity (IP) would work well to define the mineralisation at Lone Wolf and this is the
planned next step before further drilling is undertaken later in the current season.
The Company also drilled a series of Aircore lines along strike from the Lone Wolf
artisanal workings with many holes encountering anomalous gold in the range of 30100ppb gold. The end of hole samples will be sent for multi-element analysis to allow
further geochemical discrimination using pathfinder elements. Due to the
reconnaissance nature of the drilling, true heel-toe coverage was not achieved and thus
it is likely that other pods of mineralisation exist in the near vicinity and these should be
detectable using geophysics (IP).
2
Figure 1: Lone Wolf aerial view showing drillhole locations
and traces relative to granite contact
Figure 2: Lone Wolf aerial view showing drillhole locations
relative to artisanal workings.
XX June 2021
Final Aircore and Auger drilling results
Initial (gold only) results have now been received for all outstanding Aircore and auger
drilling at Tabakorole, with end of hole samples remaining to be sent off for multielement analysis overseas.
The previously reported Target H results were followed up with 3 further lines of Aircore
and included one potentially economic intercept of 7m at 2.1g/t Au and ending in
mineralisation.
Target I encountered several high gold values with peaks of 2m at 5.2g/t and 2m at
0.33g/t while Target J returned a peak value of 2m at 0.49g/t with moderately
anomalous gold ranging between 30-80ppb encountered on adjacent lines.
Importantly these results demonstrate the presence of mineralisation at these targets
and the results are planned be followed up with IP concurrently with Lone Wolf.
Figure 3: Results at Targets H, I and J.
This announcement has been approved for release by the Board.
For further information, please contact:
Chris van Wijk
Managing Director
T: +61 8 9200 4960
Amalie Schreurs
White Noise Communications
amalie@whitenoisecomms.com
T: +61 431 636 033
For more information, visit www.marvelgold.com.au.
Competent Person’s Statement
The information in this announcement that relates to exploration results at Tabakorole
is based on information compiled by Company geologists and reviewed by Mr Chris van
Wijk, in his capacity as Managing Director of Marvel Gold Limited. Mr. van Wijk is a
Member of the Australian Institute of Mining and Metallurgy and has sufficient
experience which is relevant to the style of mineralisation and type of deposit under
consideration and to the activity which he is undertaking to qualify as a Competent
Person as defined in the 2012 edition of the Australasian Code for Reporting of
Exploration Results, Mineral Resources and Ore Reserves (2012 JORC Code). Mr. van Wijk
consents to the inclusion in the report of the matters based upon the information in the
form and context in which it appears.
Reference to previous ASX announcements
In relation to the announcement of the Tabakorole Mineral Resource estimate on 5
October 2021, the Company confirms that it is not aware of any new information or data
that materially affects the information included in that announcement and that all
material assumptions and technical parameters underpinning the Mineral Resource in
that announcement continue to apply and have not materially changed.
In relation to the exploration results included in this announcement, the dates of which
are referenced, the Company confirms that it is not aware of any new information or
data that materially affects the information included in those announcements.
5
About Marvel Gold
Marvel Gold Limited is an Australian resources company listed on the Australian Securities
Exchange under stock code MVL. Marvel is a Mali-focused gold explorer with advanced gold
exploration projects and extensive landholdings in South Mali.
The Tabakorole Gold Project has a JORC Mineral Resource of 1.025Moz grading 1.2 g/t gold (see
ASX announcement dated 5 October 2021), with strong growth prospects along strike and via
near-deposit prospectivity over an extensive landholding in excess of 800km2. Tabakorole is held
through 100%-owned licences as well as two separate joint ventures, with Oklo Resources
Limited (ASX: OKU) (Oklo JV), in which the Company holds an 80% interest) and with Altus
Strategies plc (Altus JV), in which the Company currently holds a 70% interest, moving towards
75% through committed expenditure.
Following the spin-off of the Chilalo Graphite Project to ASX listed graphite company, Evolution
Energy Minerals Limited (ASX Code: EV1), Marvel holds 50 million shares in Evolution
Marvel has an experienced board and management team with specific skills, and extensive
experience, in African based exploration, project development and mining.
Tabakorole Mineral Resource Estimate as at 5 October 2021 (JORC 2012)
Indicated
Inferred
Total
Mt
Au
(g/t)
koz
(Au)
Mt
Au
(g/t)
koz
(Au)
Mt
Au
(g/t)
koz
(Au)
Oxide
1.4
1.2
50
1.3
1.3
55
2.7
1.3
110
Fresh
7.8
1.2
310
16.0
1.2
610
23.8
1.2
915
Total
9.2
1.2
360
17.3
1.2
665
26.5
1.2
1,025
Note: Reported at a cut-off grade of 0.6 g/t Au, differences may occur due to rounding.
Marvel Gold Project Location Map
6
Appendix 1. Table of Significant Intercepts (>3m at 0.5g/t Au).
Prospect
Hole ID
Hole
Type
East
North
Dip
Azi
EOH
(m)
From
To
Au
(g/t)
Intercept
Lone Wolf
22TBKRC017
RC
675005
1196070
-60
240
85
1
7
1
6m at 1.0g/t
Lone Wolf
22TBKRC017
RC
675005
1196070
-60
240
85
64
75
0.9
11m at 0.9g/t
Lone Wolf
22TBKRC018
RC
675029
1196096
-60
230
85
Lone Wolf
22TBKRC019
RC
675010
1196010
-60
50
85
Lone Wolf
22TBKRC020
RC
675088
1196001
-60
50
80
Lone Wolf
22TBKRC021
RC
675064
1195975
-60
50
80
16
24
1.8
8m at 1.8g/t
Lone Wolf
22TBKRC021
RC
675064
1195975
-60
50
80
33
47
4.9
14m at 4.9g/t
Lone Wolf
22TBKRC021
RC
675064
1195975
-60
50
80
55
65
1.9
10m at 1.9g/t
NSI
63
67
0.9
4m at 0.9g/t
NSI
Appendix 2: Reconnaissance drilling details
Significant results in reconnaissance drilling defined as MaxAu >0.1g/t Au.
Prospect
HoleID
East
North
Dip
Azi
EOH
From
To
Width
22TBKAC0323
Hole
Type
AC
674519
1196568
-60
225
43
2
4
2
MaxAu
(g/t)
0.12
Tabakorole
Tabakorole
22TBKAC0326
AC
670838
1200419
-60
225
30
18
20
2
0.65
Tabakorole
22TBKAC0332
AC
670966
1200547
-60
225
30
24
26
2
0.11
Tabakorole
22TBKAC0343
AC
671201
1200776
-60
225
18
10
12
2
0.14
Tabakorole
22TBKAC0344
AC
671096
1200537
-60
225
23
20
22
2
0.15
Tabakorole
22TBKAC0349
AC
671203
1200647
-60
225
15
2
4
2
0.18
Tabakorole
22TBKAC0350
AC
671226
1200669
-60
225
14
0
2
2
0.17
Tabakorole
22TBKAC0358
AC
671210
1200515
-60
225
24
12
14
2
0.13
Tabakorole
22TBKAC0481
AC
671655
1200128
-60
225
28
24
26
2
0.55
Tabakorole
22TBKAC0483
AC
671697
1200171
-60
225
30
22
24
2
0.17
Tabakorole
22TBKAC0485
AC
671740
1200213
-60
225
23
4
6
2
0.11
Tabakorole
22TBKAC0486
AC
671761
1200233
-60
225
26
18
20
2
0.41
Napanyala
22TBKAC0499
AC
677627
1192449
-60
240
60
8
10
2
0.33
Napanyala
22TBKAC0504
AC
677757
1192524
-60
240
34
30
32
2
5.24
Napanyala
22TBKAC0546
AC
678837
1191771
-60
240
41
16
18
2
0.49
Sirakourou
22TBKAC0603
AC
661785
1201291
-60
240
32
24
26
2
0.21
Sirakourou
22TBKAC0605
AC
661837
1201321
-60
240
28
10
12
2
0.11
Sirakourou
22TBKAC0609
AC
661941
1201381
-60
240
34
22
24
2
0.16
Tabakorole
22TBKAG0346
AUG
673807
1198571
-90
0
9
8
9
1
0.64
Tabakorole
22TBKAG0397
AUG
672450
1198786
-90
0
11
10
11
1
0.13
Sirakoroble
22TBKAG2435
AUG
668480
1193906
-90
0
7
6
7
1
0.12
Sirakourou
22TBKAG2465
AUG
668480
1194304
-90
0
8
7
8
1
0.31
7
Appendix 3. JORC Table 1 Reporting.
Section 1 - Sampling Techniques and Data
Criteria
Sampling
Techniques
Drilling
techniques
Drill Sample
Recovery
Logging
Sub-Sampling
techniques
and sample
preparation
Explanation
Nature and quality of sampling (eg
cut channels, random chips, or
specific specialised industry standard
measurement tools appropriate to
the minerals under investigation,
such as down hole gamma sondes, or
handheld XRF instruments, etc).
These examples should not be taken
as limiting the broad meaning of
sampling.
Aspects of the determination of
mineralisation that are Material to
the Public Report.
Commentary
Auger samples are collected by spear sampling at the soil-saprolite interface and
end of hole.
Aircore samples are collected by spear sampling every 1m interval and then
combined to make a 2m composite.
RC samples are collected by riffle splitting samples directly from the cyclone every
1m.
Drill type (eg core, reverse
circulation, open-hole hammer,
rotary air blast, auger, Bangka, sonic,
etc) and details (eg core diameter,
triple or standard tube, depth of
diamond tails, face-sampling bit or
other type, whether core is oriented
and if so, by what method, etc).
Method of recording and assessing
core and chip sample recoveries and
results assessed.
Auger, Aircore and RC drilling were used for reconnaissance. Auger holes were
drilled vertically whilst Aircore and RC are generally drilled at -60 from horizontal
to try and achieve heel-toe coverage. Shallow RC drilling is used where Aircore
cannot penetrate the lateritic profile.
Measures taken to maximise sample
recovery and ensure representative
nature of the samples.
Whether a relationship exists
between sample recovery and grade
and whether sample bias may have
occurred due to preferential
loss/gain of fine/coarse material.
Whether core and chip samples have
been geologically and geotechnically
logged to a level of detail to support
appropriate
Mineral
Resource
estimation, mining studies and
metallurgical studies.
Whether logging is qualitative or
quantitative in nature. Core (or
costean, channel, etc) photography.
The total length and percentage of
the relevant intersections logged.
If core, whether cut or sawn and
whether quarter, half or all core
taken.
Spear samples are collected by sampling across the sample pile to try and get as
representative a sample as possible.
A riffle splitter is considered industry standard for collection of RC samples.
The drilling reported herein is reconnaissance in nature designed to test shallow
subsurface anomalies. Grade/recovery relationship is not assessed.
If non-core, whether riffled, tube
sampled, rotary split, etc and
whether sampled wet or dry.
For all sample types, the nature,
quality and appropriateness of the
sample preparation technique.
Reconnaissance samples are spear sampled. RC samples are riffle split off the
cyclone.
Quality control procedures adopted
for all sub-sampling stages to
maximise representivity of samples.
All samples are prepared by an independent laboratory: samples are crushed to 2mm and a 1000g sub-sample is pulverised to 85% passing 75 microns. Gold has
been determined by fire assay/AAS based on a 50g charge.
Not applicable – no estimation of sample recovery has been undertaken.
Drilling data is routinely logged using the company system for Diamond and RC
logging which captures lithology, alteration and geological observations. Auger and
Aircore reconnaissance drilling is not deemed suitable for use in Resource
Estimation.
Logging is qualitative as above.
All samples are geologically logged.
Not applicable – no core drilling reported.
Sample preparation consisted of jaw crushing to -2mm, splitting 1000 grams and
pulverizing to 85% passing 75µ. A sub-sample of 150-200g (pulp sample) is retained
for analysis. The sample preparation procedures carried out are considered
industry standard.
Field duplicates and Blanks have been used to monitor laboratory QAQC.
8
Criteria
Quality
of
assay
data
and
laboratory
tests
Verification of
sampling and
assaying
Location of
data points
Data spacing
and
distribution
Orientation
of data in
relation to
geological
structure
Explanation
Measures taken to ensure that the
sampling is representative of the insitu material collected, including for
instance
results
for
field
duplicate/second-half sampling.
The
nature,
quality
and
appropriateness of the assaying and
laboratory procedures used and
whether the technique is considered
partial or total.
Commentary
Field Duplicates are the primary means of ensuring representativeness of sampling.
Duplicates and blanks have been used to ensure assay quality and
representativeness of sampling.
For geophysical tools, spectrometers,
handheld XRF instruments, etc, the
parameters used in determining the
analysis including instrument make
and
model,
reading
times,
calibrations factors applied and their
derivation, etc.
Nature of quality control procedures
adopted (eg standards, blanks,
duplicates,
external
laboratory
checks) and whether acceptable
levels of accuracy (ie lack of bias) and
precision have been established.
Not Applicable – no geophysical data reported.
The verification of significant
intersections by either independent
or alternative company personnel.
Samples have been verified by Rocksolid Data Consultants who are independent
Database adminstrators.
The use of twinned holes.
Not applicable – no twin drilling reported.
Documentation of primary data, data
entry procedures, data verification,
data storage (physical and electronic)
protocols.
Discuss any adjustment to assay data.
Accuracy and quality of surveys used
to locate drill holes (collar and downhole surveys), trenches, mine
workings and other locations used in
Mineral Resource estimation.
Specification of the grid system used
Quality and adequacy of topographic
control
All sample details are recorded on paper in the field before being transferred to
spreadsheets which are then validated and imported into a Datashed database,
administered in Perth, Western Australia.
Data spacing for
Exploration Results.
of
Reconnaissance drill spacing is variable. Generally first pass hole spacing is on the
order of 50m between holes and 200m between lines of holes.
Whether the data spacing and
distribution is sufficient to establish
the degree of geological and grade
continuity appropriate for the
Mineral Resource and Ore Reserve
estimation
procedure(s)
and
classifications applied.
Whether sample compositing has
been applied.
Reconnaissance drilling is not considered appropriate for inclusion in Mineral
Resource reporting.
RC drilling is appropriate for inclusion into future mineral resources however there
is not sufficient drill density at Lone Wolf to allow this at the current time.
Whether the orientation of sampling
achieves unbiased sampling of
possible structures and the extent to
which this is known, considering the
deposit type.
If the relationship between the
drilling
orientation
and
the
orientation of key mineralised
structures is considered to have
Reconnaissance drilling is generally oriented perpendicular to structure as
interpreted from the magnetic data to try and eliminate bias.
reporting
All samples were assayed for gold by fire-assay with AAS finish by SGS Laboratories
in Bamako, Mali. This is considered to be a total analysis for Gold.
Field duplicates and Blanks were used for laboratory quality control.
No assay data was adjusted, and no averaging was employed
Final sample locations and drillhole collars were recorded using handheld GPS with
3-5m accuracy.
All results reported use WGS84 UTM Zone 29.
Not applicable.
Aircore samples are composited to 2m samples. RC samples are not composited.
Not applicable – no bias known.
9
Criteria
Commentary
Sample
Security
Explanation
introduced a sampling bias, this
should be assessed and reported if
material.
The measures taken to ensure
sample security.
Audits or
reviews
The results of any audits or reviews of
sampling techniques and data.
No audits have been conducted.
Samples were stored on site in the field camp until despatch. Samples were bagged
and consolidated into sacks secured with zip ties. A contracted transport company
was used to collect the samples and transport them by road to the laboratory in
Bamako. A chain of custody was maintained at all times.
Section 2 - Reporting of Exploration Results
Criteria
Mineral
tenement and
land tenure
status
Exploration
done by other
parties
Explanation
Type, reference name/number,
location and ownership including
agreements or material issues with
third parties such as joint ventures,
partnerships, overriding royalties,
native title interests, historical sites,
wilderness or national park and
environmental settings.
The security of the tenure held at the
time of reporting along with any
known impediments to obtaining a
licence to operate in the area.
Acknowledgment and appraisal of
exploration by other parties.
Commentary
The Tabakorole, Sirakoroble Sud and Npanyala licenses are held under JV
with Altus Strategies plc. The joint venture is the owner of Legend Gold
Mali SARL, which is the 100% owner of the licences. The Solabougouda
and Sirakourou licences are held under JV with Oklo Resources.
The Tabakorole exploration licence is in its final period and was renewed
under Arrêté N°2020-3933 on the 31st December 2020 and is valid for 3
years.
The N’panyala license was granted under Arrêté N°2021-4911 on the 25th
November 2021 and is valid for 3 years.
Sirakoroblé Sud was granted under Arrêté N°2021-5044 on the 2nd of
December 2021 and is valid for 3 years.
The Sirakourou license is currently under renewal.
Solabougouda was granted under Arrêté N°2019-3527 on the 10th of
October 2019 and is valid for 3 years.
There are no known impediments to operating on any of the licences.
The Tabakorole project was initially covered by regional geochemical sampling by
BRGM in the 1950’s, however the first mining company to carry out work on the
license area was BHP in 1993. The first drilling was conducted by Ashanti Gold
Company in 2001. A comprehensive work history has been detailed in the
Announcement dated 17th June 2020.
The majority of the work carried out subsequently has been by Legend Gold.
Geology
Deposit type, geological setting and
style of mineralisation
The Tabakorole ore deposit as it is currently recognised is an orogenic,
hydrothermal gold deposit with much in common with other volcano-sedimentary
hosted Birimian style orogenic gold deposits throughout the region.
Drill
hole
information
A summary of all information
material to the understanding of the
exploration results including a
tabulation
of
the
following
information for all Material drill
holes:
All relevant summary information is reported.
o easting and northing of the
drill hole collar
o elevation or RL (Reduced
Level – elevation above sea
level in metres) of the drill
hole collar
o dip and azimuth of the hole
o down hole length
interception depth
and
o hole length.
10
Criteria
Data
aggregation
methods
Relationship
between
mineralisation
widths
and
intercept
lengths
Explanation
In reporting Exploration Results,
weighting averaging techniques,
maximum and/or minimum grade
truncations (eg cutting of high
grades) and cut-off grades are usually
Material and should be stated.
Commentary
For RC drilling, Significant Intercepts are defined as >3m at a cutoff grade of 0.5g/t
Au and no more than 4m of internal waste.
Where
aggregate
intercepts
incorporate short lengths of highgrade results and longer lengths of
low-grade results, the procedure
used for such aggregation should be
stated and some typical examples of
such aggregations should be shown
in detail.
Only standard sample lengths with a minimum of 1m were used and are reported
as intercepts using criteria as outlined above.
The assumptions used for any
reporting of metal equivalent values
should be clearly stated.
No metal equivalents are reported.
These relationships are particularly
important in the reporting of
Exploration Results.
Mineralisation at Lone Wolf is thought to be sub-vertical. As such, all reported
intercepts are down hole intercept lengths.
For reconnaissance drilling, all samples reporting above 0.1g/t Au are reported.
If the geometry of the mineralisation
with respect to the drill hole angle is
known, its nature should be
reported.
If it is not known only the down hole
lengths are reported, there should be
a clear statement to this effect (eg
‘down hole length, true width not
known’).
Diagrams
Appropriate maps and sections (with
scales) and tabulations of intercepts
should be included for any significant
discovery being reported These
should include, but not be limited to
a plan view of drill hole collar
locations and appropriate sectional
views.
See body of announcement for diagrams.
Balanced
reporting
Where comprehensive reporting of
all Exploration Results is not
practicable, representative reporting
of both low and high grades and/or
widths should be practiced to avoid
misleading reporting of Exploration
Results.
All results from the current program have been shown within the reported
Diagrams. All anomalous drill samples have been reported within the Tables.
Other
substantive
exploration
data
Other exploration data, if meaningful
and material, should be reported
including (but not limited to):
geological observations; geophysical
survey results; geochemical survey
results; bulk samples – size and
method of treatment; metallurgical
test
results;
bulk
density,
groundwater, geotechnical and rock
characteristics; potential deleterious
or contaminating substances.
All applicable geological observations have been reported at this time.
Further work
The nature and scale of planned
further work (eg tests for lateral
extensions or depth extensions or
large-scale step-out drilling).
Further work is dependent on the results of a planned IP survey due to start in the
first half of 2022.
11
Criteria
Explanation
Diagrams clearly highlighting the
areas of possible extensions,
including the main geological
interpretations and future drilling
areas, provided this information is
not commercially sensitive.
Commentary
12
Share your feedback
Discover